Wat is PDF Literature ACU-RITE 200S PDF

ACU-RITE 200S PDF

Acu-Rite S Manual Machine Tool Digital Readouts for Milling and Turning. Acu-Rite S DRO packages with Linear Encoders for almost any manual. Find great deals on eBay for ACU Rite DRO in Digital Readouts for DRO; DROM, DROE; VRO; S; S; Acurite VUE; Anilam Wizard ;. Acu-Rite S DRO. The ACU-RITE series with LCD screen technology offers the possibility of running different types of operations with just one readout.

Author: Doran Fautilar
Country: Poland
Language: English (Spanish)
Genre: Education
Published (Last): 6 October 2011
Pages: 469
PDF File Size: 16.80 Mb
ePub File Size: 7.66 Mb
ISBN: 126-4-38252-900-7
Downloads: 83807
Price: Free* [*Free Regsitration Required]
Uploader: Daigul

Job setup parameters, Units, Scale factor – ACU-RITE 200S User Manual

SETUP acu-rrite key is displayed. The X axis scale seems to be working fine when plugged into the Y axis input. You are led step by step through the most important settings until the device is ready for operation.

The following steps may have already been completed by the installer. The sum of the Z positions will be displayed on the Z0 display and the Z display will be blanked.

Data Output; Zero, and Next Hole. Press it again to stop time from elapsing. The encoder resolution and count direction can also be established by just moving each axis. They havent been released yet, but they look sweet as all get out.

The Actual Value mode always displays the current actual position of the tool, relative to the active datum. Your old scales are most likely 10um, but Ziggy nailed it right on the money.

Acu-Rite DRO

Range error on the value to fetch the tangent of. The Actual Value mode always displays the current actual position of the tool, relative to the active datum. Page 19 I – 1 Fundamentals of Positioning Encoder Reference Marks Encoders normally contain one or more reference marks which the S Reference Mark Evaluation feature uses to re-establish datum positions after a power interruption.

  74LS76N DATASHEET PDF

Serial Port A printer or computer may be connected to the serial port. This form is used to set a nominal position. Resetting will stop the clock if it is running. Each acuu-rite provides specific fields for entering the required information. In this case the error can be compensated by the calculation acu–rite a single correction factor. The following table defines the Zero Angle where the position of the angle is zero for the three possible planes of rotation.

This error can be compensated for by inputting the amount of backlash ack-rite the lead screw into the Backlash Compensation feature.

Diameter Axes Select Diameter Axes to bring up the diameter screen shown here to set which axes can be displayed in either radius or diameter values. The square root of acu-riite negative number is undefined. Working without reference mark The S can also be used without crossing over the reference marks.

Printer with serial data interface.

Also shop in Also shop in. The position of the centerline M is determined by probing the edges 1, and 2. The access code is Readout Parameter Access Code An access code must be entered before machine-related installation parameters can be set or changed. Tell us about it. I – 3 Milling Specific Operations I – 3 Milling Specific Operations This section discusses operations and soft key functions specific to milling applications only.

Encoders that have marks separated by ach-rite specific encryption pattern allows 200e S to use any two pair of acu-eite along the length of the encoder to re-establish the prior datums. Used to divide the current position by two page Linear Error Compensation Linear error compensation can be applied, if the results of the comparison with a reference standard show a linear deviation over the whole measuring length.

Page 40 I – 3 Milling Specific Operations Only the tools set using the same reference surface may be changed without having to reset the datum.

  LOGIQUE PROPOSITIONNELLE PDF

Note that any movement that occurs while power is off will be lost. Reading the Graph The error compensation table may be viewed in table or graphical formats. The current selection is shown on the soft key and in the plane field. Enabling Z0, and Z Coupling To couple the Zand Z axes and have the result displayed on the Z display, press and hold the Z key approximately 2 seconds.

Readout Parameter Access Code Readout Parameter Access Code An access code must be entered before machine-related installation parameters can be set or changed. Length of the taper ON indicates that the axis position will be displayed as a diameter value. Page 29 I – 2 General Operations for S Measured Value Output With the measured value output feature, probe measurement values can be sent over the serial port. I – 3 Milling Specific Operations Probing with a Tool If using a tool, or non-electrical edge finder to set datum points, the S probing functions can still be used.

Tell us what’s missing. It is defined as one of the two axes in the plane of rotation. The following listed fields require data input. Incremental workpiece positions A position can also be referenced to the preceding nominal position. Display Configuration Display Configuration The Display Configuration form is where which axes can be selected for display, and in what order.

AcuRite S Digital Readout

Originally Posted by spaeth. SETUP soft key, and enter the passcode. It acu-rute defined as one of the two axes in the plane of rotation.

First time power up require these values to be defined along with all initial DRO setting.