HC393 DATASHEET PDF
Rev. 6 — 3 December Product data sheet. Table 1. Ordering information. Type number Package. Temperature range Name. Description. Version. when gated with the Clock of the HC .. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in. HC datasheet, HC circuit, HC data sheet: TI – DUAL 4-BIT BINARY COUNTERS,alldatasheet, datasheet, Datasheet search site for Electronic.
|Published (Last):||10 April 2006|
|PDF File Size:||18.52 Mb|
|ePub File Size:||8.38 Mb|
|Price:||Free* [*Free Regsitration Required]|
Again, this is a standard problem in digital design, but it is seldom worthwhile to make one’s own. Doubled, this will give V. Any dimension in brackets or parenthesis are for reference only.
However, the classic JK flip-flop is level-sensitiveand does not depend on the quality of edges or speed of response. TIs provision of technical, application or other design advice, quality characterization, reliability data or other services or information,including, but not limited to, reference designs and materials relating to evaluation modules, collectively, TI Resources are intended toassist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in anyway, Designer individually or, if Designer is acting on behalf of a company, Designers company agrees to use any particular TI Resourcesolely for this purpose and subject to the terms of this Notice.
The HC contains two 4-bit counters, each containing four cascaded divide-by-two stages. Connect the clocks together and control them with the pushbutton.
An HC08 is below the leftmost counter, for which it serves as reset logic. What you want is one that is normally closed one way, and springs back when pressed and released.
Pulses to be counted are applied to the clock input of the first flip-flop, which toggles on every pulse. If we interpret them as a binary number, the first digit is the most significant bit msband the second one the least significant bit lsb.
This is the oscillator I intend to use when I build a clock. Make this alteration, and see that you now have a modulo counter. Both S and R should not simultaneously be high, or the circuit will not enter a predictable state. This frequency is not precisely stable in the short term, but over longer intervals, of perhaps a day, it is adjusted by speeding up or slowing down the alternators so that a clock based on it does not gain or lose time.
One output gives a negative pulse usually used for counter clocks and the other gives a positive pulse. This can be continued for any number of flip-flops, each one of which will represent a binary digit.
Such accuracy in a mechanical watch comes at a very great price, if it is available at all. Feedback is supplied by the k resistor and the crystal.
Textbooks seem to give useless methods of self-correction. TI bases its knowledge and belief on informationprovided by third parties, and makes no representation or warranty as to the accuracy of such information. Therefore, it is necessary that a Johnson counter have a self-correction circuit that removes any erroneous states.
Then, the construction of a digital clock with a Nixie display is described. The three principal types of counters have been studied above, so that you know their fundamentals, their advantages and their drawbacks. Note that only one element has to be lighted, and a single dropping resistor used. You must log in or sign up to reply here. The output is a 0. If you are using only one chip, tie them both high.
By cascading two modulo counters and a modulo counter, you now have an electronic escapement for a clock, which is fed by a 1. We will use the modulo-5 section, and arrange that it resets when it reaches 4.
A glance at the logic diagrams for these chips show that the decoding is not as simple as for a Johnson counter.
Hc393 datasheet pdf
datzsheet In data sheets, bit inputs are represented by letters A, B, C Only the first, lowest-order counter has ENT tied high.
When that time arrives, the seconds counter is again enabled. Two LS93’s would give us modulusin the same way. For the rapid change, 1 kHz would go through datxsheet hours in It is arranged so that the next clock when at 9 brings the counter back to If you are building a clock, you will need two of these counters, one to count seconds up to minutes, the other to count minutes up to hours.
Nevertheless, it is the only use of CO, which cannot be considered a “terminal count” or TC in any sense, such as a synchronous binary counter produces. These are stress ratings only, andfunctional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is notimplied. The 32, Hz crystal is a small cylinder the very small watch crystals are too small to be practical; be sure you get one of the larger ones, about 2.
Stuffing a PC board is just stuffing a PC board, and only shows you what the components look like.
HC Datasheet, HC PDF – Free Datasheets, DUAL 4-BIT BINARY COUNTERS
This leaves only 4 for controls, so the chip is very simple to use. This is a standard exercise in digital design, to texts of which the reader is referred for general methods. The counter will not count unless both are high. There are Datasheeh and LS’s as well.
The output of the minutes counter is also routed through the data selector to the hours counter.