Wat is PDF Literature IPMP CONFIGURATION IN SOLARIS 10 PDF

IPMP CONFIGURATION IN SOLARIS 10 PDF

These topics include IPv4 and IPv6 network configuration, managing TCP/IP 1. Oracle Solaris TCP/IP Protocol Suite (Overview) The default is 10 seconds. Oracle Solaris Administration: IP Services Oracle Solaris 10 1/13 Information An IPMP configuration typically consists of two or more physical interfaces on the . For IPMP configuration tasks, refer to Chapter 31, Administering IPMP (Tasks). Oracle Solaris IPMP involves the following software: You can configure one of the interfaces down to 10 megabits and still place the two interfaces into the.

Author: Shaktizahn Zulkizuru
Country: Panama
Language: English (Spanish)
Genre: Love
Published (Last): 4 March 2012
Pages: 488
PDF File Size: 8.12 Mb
ePub File Size: 2.43 Mb
ISBN: 661-6-39004-470-6
Downloads: 16970
Price: Free* [*Free Regsitration Required]
Uploader: Vigis

How to configure Solaris 10 Probe based IPMP

Created new logical interface hme0: Similarly, if you configure as standby an interface that already has data addresses, these addresses automatically fail over to another interface in the IPMP group.

The port on the switch does not transmit or receive packets.

IP Security Architecture Overview. Any attempt to create this type of configuration will fail. This process is called load spreading. The dummy address was created so that hme0 can still be accessed.

IPMP does not permit you to add a data address to an interface that is configured through the ifconfig command as configurstion. You can observe this flag in the status lines confjguration the interface in the ifconfig output. Configuring IKE Tasks You can always view the current status of an interface by typing ifconfig interface.

Internet Key Exchange Overview Link-based failure detection, if supported by the NIC driver Probe-based failure detection, when test addresses are configured Detection of interfaces that were missing at boot time The in.

  EL CHIVO EXPIATORIO RENE GIRARD PDF

The standard IPv4 and, if applicable, IPv6 packet traffic through an interface is considered to be data traffic. If a system has multiple interfaces attached to the same link, you can configure IPMP to perform failover if one of the interfaces fails.

Detecting Physical Interface Repairs For the in. To turn on the failover attribute of the address, you would use the failover option without the dash. A single interface can be configured in its own IPMP group. Paid Training Courses we Offer. Here i have removed the LAN cable from eg1 and let see what happens.

IPMP Configuration – Solaris 10 vs Solaris 11 –

In IPMP terminology, an IP link is a communication facility or medium over which nodes can communicate at the data-link layer of the Internet protocol suite. IP Security Architecture Overview. Consider the example of four VLANs, bgebgebgeand bge If you need additional data IP addresses you should add them as deprecated IP interfaces. NIC qfe0 of group testgroup1 is not plumbed for IPv6 and may affect failover capability.

When the repair of a failed interface is detected, network access fails back to the repaired interface, as described in IPMP Failure Detection and Recovery Features. This can be done in two ways. The transmit or receive path of the interface has failed. This section introduces solarus and concepts that are used throughout the IPMP chapters in this book. Multicast memberships that are associated with This chapter contains the following information: You can add new interfaces to an existing group on a live system.

  MANEJO DEL TEODOLITO ELECTRONICO PDF

You can check the status of an interface by issuing the ifconfig interface command. The first few hosts that respond to the echo packets are chosen as targets for probing. Your email address will not be published.

However, failover and failback cannot occur for an IPMP group configueation only one interface. If one interface in the group is to become the standby interface, do not configure a test solaria for that interface at this time. The Primary Administrator role includes the Primary Administrator profile. So you will be not able to perform the above test. You can observe this flag in the status lines for the interface in the ifconfig output.

How to configure Solaris 10 IPMP ? – UnixArena

Its very clear and simple. Do not use DHCP on data addresses. In order to post comments, please make sure JavaScript and Cookies are enabled, and reload the page. However, hme0 does not have a test address configured. Data addresses are the conventional IPv4 and IPv6 addresses that are assigned to an interface of a NIC at boot time or manually, through the ifconfig command.