Wat is PDF Environment M68 CCO TM PDF


ARMY TM &P* AIR FORCE TO 11W TECHNICAL M68 SIGHT, REFLEX, W/QUICK RELEASE MOUNT AND SIGHT MOUNT M68 Cco Tm Manual Army – p s – scribd TM. CHAPTER I. PRESENTATION. Aimpoint CompM4 Reflex Sight is a rugged precision red dot Sight developed mainly for military and law enforcement. M68 SIGHT, REFLEX, W/QUICK RELEASE MOUNT AND SIGHT MOUNT CLOSE COMBAT OPTIC (CCO) (NSN ) (NSN ).

Author: Dam Kigazil
Country: Seychelles
Language: English (Spanish)
Genre: Automotive
Published (Last): 17 April 2015
Pages: 413
PDF File Size: 7.83 Mb
ePub File Size: 8.73 Mb
ISBN: 489-8-46686-510-3
Downloads: 22559
Price: Free* [*Free Regsitration Required]
Uploader: Yozshushicage

Technical Manual Close Combat rifle combat optic technical manual operator and field maintenance manual tm p chapter 1: The first is unauthorized intentional modification to the sights battery housing assembly by bending the prongs on the 6-pronged clip.

Install battery cap and holder assembly by turning clockwise until snug. Dust Storms and Sandstorms. Base assembly damaged in such a way that sight cannot be installed. Keep spare batteries in your inner pockets to keep them warm. When unserviceable, condemn and dispose of the Zitem at the level of maintenance shown in the third position of the SMR code.

This is necessary since figures are prepared for assembly groups and subassembly groups, and lists are divided into the same groups. The least preferred battery should only be used in an emergency or when all efforts to attain the recommended battery or preferred alternatives have failed and your mission cannot be completed without the use of the least preferred alternative. For the M16A2 rifle, the special spaced spacer is not required. Tmm zeroing is accurate, fire three more shots to confirm.


Remove battery cap 1 by turning it counterclockwise. The process of investigating and detecting the cause of equipment malfunctioning; the act of isolating a fault within a system or Unit Under Test UUT. Refer to NOTE below. Source Code XX 1st two positions: To adjust specified variable elements of an item to bring about optimum or desired performance.

Each work package provides specific information that will tn you in performing co various operational and dco tasks. The work time figure represents the average time required to restore an item assembly, subassembly, component, module, end item, or system to a serviceable condition under typical field operating conditions.

Remove front and rear lens covers 1 from sight 3. Serial number is located on m668 bottom of the sight. If necessary, you can also run water through the honeycomb to clear it. Zero weapon WP 00, page Install both lens covers on the torque knob 3 when not on the lens. Insert O-ring 5 around holder housing 4.

The recommended location is with the front end of the mount lined up with front end of the upper receiver.

If you cannot correct it yourself, notify your armorer. To remove and install the same item when required to perform service or other maintenance functions.

TM 9-1240-413-13&P S60288

Replace battery cap 1 by turning it clockwise until snug. The replace function for this level of maintenance is indicated by the cc “H” appearing in the third position of the SMR code. NOTE Before installing adjustment caps, inspect threads and adjustment caps to ensure that they are free of damage, moisture and dirt, and that the O-rings are installed. When mounting on the M16A2 rifle, the spacer is removed.

Army Publishing Directorate

Insert O-ring 2 around battery cylinder housing 3. If the item is authorized to you by the third position code of the SMR code, but the source code indicates it is made at higher level, order the item mm68 the higher level of maintenance.


Replace adjustment screw cap 1 by turning clockwise until snug. Open rear lens cover 1.

If not using iron sights for initial zeroing, go directly to step 8. This j68 is assigned to the entry in the listing for referencing when required. While corrosion is typically associated with rusting of metals, it can also include deterioration of other materials such as rubber or plastic.

For Tactics, Techniques and Procedures Thursday, we are continuing our discussion on optics. Turn adjustment screw as follows: Keep front and rear lens covers closed when sight is not being used. Following this rough alignment, red dot has no use with iron sights. Functions to this level of maintenance are identified by work cxo figure in the H column of column 4and an associated reference code is used in the REMARKS column 6.

N68 publication is required for administration and operational purposes, as determined 14 April Repair parts for reparable special tools are also listed in a separate work package.

Remove switch knob 2 from fco 3. Refer to TM Other requests for this document shall be referred to: Carefully clean the contacts in the bottom of the battery compartment, then reinstall battery Comp M2: